MimioProjector Laser 320LT, 3200LT (ULTRA-WIDE)

Guides, Specifications, and Documentation

Need extra guidance? Check out our additional resources: 320LT Spec Sheet | 3200LT Spec Sheet | Laser Curtain Quick Start Guide | Choosing and Installing a Whiteboard for a Touch Projector | Connecting the MimioProjector to the Classroom Computer: Do’s and Don’ts | Warranty | USB Cabling Guide for Interactive Devices | Cable Troubleshooting Guide

Common FAQS

  1. I cannot bring up the calibration screen when using the MimioProjector™ device. Read More >>
    If you open MimioStudio Notebook, does MimioProjector show up under Tools > Settings > Classroom Devices (on a PC) or Notebook > Preferences > Classroom Devices (on a Mac)? If not, there may be a connection issue. For your MimioProjector device to be interactive, you need to have an IR module installed. You also need to have the USB cable connected to the MimioProjector device from the computer, as well as either an HDMI or VGA cable. Make sure that you are using the standard USB cable that ships with your MimioProjector device. If a USB extender is required, we recommend using a USB 1.1 extender over a CAT5E or CAT 6 connection. We have tested this extension successfully up to 150 feet. Once the IR module is installed and the cables are connected, make sure that the module is turned on. To do so, press “Menu” on the MimioProjector remote and scroll down to “Interactive Settings.” It will say “IR Camera” if it is turned on, or “Off” if it is turned off. If you have the IR module turned on and both cables connected, but the MimioProjector device is still not interactive, contact customercare@boxlight.com for additional troubleshooting.
  2. I cannot turn on the IR module because it is grayed out in the MimioProjector menu. Read More >>
    It is important to make sure that the IR module is inserted into the MimioProjector device correctly and that the pins are making a solid connection. If the IR module is installed correctly, make sure that both the USB cable and either an HDMI or VGA cable is connected to the MimioProjector device from the computer. Also, make sure that you are using the standard USB cable that ships with your MimioProjector device. If a USB extender is required, we recommend using a USB 1.1 extender over a CAT5E or CAT 6 connection. We have tested this extension successfully up to 150 feet. Additionally, make sure that the 3D setting is off by going to Menu > 3D, using the MimioProjector remote. If this option is turned on, it disables the IR module. If none of the above steps resolve the issue, contact customercare@boxlight.com for additional troubleshooting.
  3. I can bring up the calibration screen when using the MimioProjector device, but it will not calibrate. Read More >>
    This is most likely due to an issue with the stylus. First, try replacing the batteries in the MimioProjector stylus. If you still cannot calibrate after replacing the batteries, try using a known working stylus from another classroom. If using a known working stylus does not allow you to calibrate, there may be an issue with your IR module. Try replacing your IR module with a known working IR module from another classroom to see if this resolves the calibration issue. If none of the above steps resolve the issue, contact customercare@boxlight.com for additional troubleshooting.
  4. The MimioProjector device is connected, but there is no video displayed on the whiteboard. Read More >>
    If you see the Mimio splash page when you power on the MimioProjector device, make sure that both an HDMI cable and a VGA cable are connected to the MimioProjector device from the computer and that you have the correct corresponding source selected on the MimioProjector remote. If the image is dark when you power on the MimioProjector device, there may be an issue with the bulb. If the bulb is completely burned out, you will see a red “Lamp” light on the MimioProjector device. If all of the cables are connected and you are still not displaying an image, or if it seems like the bulb is dimming or burned out, contact customercare@boxlight.com for additional troubleshooting.
  5. All of the LEDs on the MimioProjector device are illuminated and it will not power up. Read More >>
    If all of the LEDs are illuminated, it means that the MimioProjector device is in firmware update mode, which is initiated by holding down the “Menu” button when powering on the MimioProjector device. Unplug all of the cables from the MimioProjector device, press the “Menu” button on the device a few times to make sure that it is not stuck in the down position, and then reconnect all of the cables. If all of the lights are still on when you power the MimioProjector device up, it means that it is still stuck in firmware update mode. Contact customercare@boxlight.com to request a replacement.

Note: The MimioProjector interactive projector requires version 10 or higher of MimioStudio software to function properly.

Search our complete FAQs>>

Videos

Watch our MimioProjector Laser Videos to better understand the product and setup.

 
Laser Curtain Setup

Software

Download the latest software or drivers needed for your product.

MimioStudio Software

Drivers & Calibration

Need Further Assistance?

Contact our customer care team >>